Maximum-grip surfaces
Anti-Slip Resin Bonded Surfacing
When grip is non-negotiable — ramps, steps, steep slopes and constantly wet areas — anti-slip resin bonded surfacing delivers high friction that holds in the worst conditions. Hard-wearing, UV-stable and backed by a 10-year written guarantee.
What you get
Engineered for the highest grip
Anti-slip resin bonded uses a carefully selected, slightly proud aggregate to create maximum surface friction — the right answer wherever a slip would matter most.
Maximum friction
A high-grip aggregate broadcast proud of the resin gives the strongest traction of any resin finish — built for ramps, steps and wet zones.
Holds grip when wet or icy
The texture sheds water at the surface and keeps friction in rain, frost and ice.
Hard-wearing under heavy use
A tightly bonded stone layer keeps its anti-slip texture through constant traffic rather than polishing smooth.
Targeted application
We can treat just the high-risk zones — a ramp, a threshold, a set of steps — or a whole area, as needed.
UV-stable colour
UV-resistant resin keeps the surface from fading, with contrasting aggregate available to highlight steps or edges.
Correct drainage
As a non-permeable surface, we set falls so water sheds away cleanly rather than sitting where grip matters most.
alt: Anti-Slip Resin Bonded Surfacing — finished project
alt: resin bound surface detail — close-up
Why choose us
Anti-slip surfacing is a safety measure — we treat it like one
Where you specify anti-slip surfacing, the stakes are higher: a ramp, a wet entrance, a flight of steps. We choose the aggregate grade for genuine high friction, prepare and key the base so it bonds permanently, and apply it so the texture lasts rather than wearing smooth in the first season.
Part of our resin bonded surfacing service — see the full range and how it fits together.
We can highlight hazards as well as grip them — a contrasting aggregate on a step edge or ramp transition improves visibility alongside traction, which matters for accessibility and safety.
Because the surface is non-permeable, we set falls so water moves away from the high-risk area rather than pooling on it — standing water undermines even a high-friction finish.
You receive a fixed, itemised quote with the cost per m² shown, and the surfacing is covered by our 10-year written guarantee on workmanship and materials.
Built for grip and hard use
- Fixed written quote with cost per m² shown up front
- Ground preparation and edging included — not bolted on later
- High-traction, anti-slip finish that holds grip when wet
- Drainage planned correctly for a non-permeable surface
- 10-year written guarantee on workmanship and materials
You need anti-slip resin bonded surfacing if…
- You have a ramp or steep slopeMaximum friction keeps vehicles and pedestrians safe on inclines where ordinary surfaces become risky.
- Steps need safer treadsA high-grip finish, optionally with a contrasting edge, reduces slips on stairs and thresholds.
- An entrance or area stays wetWhere water is constant, an anti-slip surface keeps reliable traction underfoot.
- Slip safety is a duty or concernFor commercial, public or shared spaces, a high-friction surface helps manage slip risk.
- An existing surface has gone slipperyAnti-slip bonded can be applied to refresh grip on a worn, polished surface.
Work process
How we apply anti-slip surfacing
The bonded sequence, with aggregate selection and detailing focused entirely on friction and safety.
Survey and risk review
We assess the hazard areas, traffic and conditions, then specify the grip level and any contrasting detailing needed.
Base preparation
We clean, repair and key the surface so the resin bonds permanently to a sound base.
Edging, falls and highlighting
We detail edges, set drainage falls and mark out any step edges or transitions to highlight.
Resin application
We apply UV-stable resin evenly at the correct coverage across the target area.
High-grip aggregate broadcast
A selected high-friction aggregate is broadcast proud of the resin for maximum anti-slip texture.
Cure, sweep and handover
Once cured we sweep off loose excess, test grip, inspect edges, clear waste and hand over a safer surface.
Materials
Trusted, industry-recognised systems
We only specify UV-stable resin and graded aggregate from
established suppliers, because the quality of the materials decides how well the surface
drains, holds colour and lasts.
FAQs
Anti-slip resin bonded questions
How much grip does anti-slip surfacing give?
It provides the highest friction of any resin finish. We select the aggregate grade to suit the hazard — a ramp, steps or a wet entrance — so the grip matches the risk.
Can you treat just the steps or ramp?
Yes. We can target only the high-risk zones or surface a whole area, whichever suits the situation and budget.
Does it stay grippy over time?
When installed correctly, yes. A keyed base, correct coverage and proud aggregate keep the texture from polishing smooth under traffic.
Can you highlight step edges?
Yes — a contrasting aggregate on edges and transitions improves visibility and accessibility alongside the grip.
Is it suitable for wet areas?
It’s designed for them. We pair the high-friction finish with correct drainage falls so water moves away rather than sitting on the surface.
Rated by homeowners across southern England
Add your verified Google reviews here. (Placeholder left intentionally —
real testimonials only, no invented reviews.)
Make a slope, ramp or entrance safer
Book a free survey. We’ll assess the hazard, specify the grip and send a fixed written quote with no obligation.